QCoDeS Example with Tektronix TPS2012¶

In [1]:

%matplotlib nbagg
import logging
from time import sleep

from qcodes.instrument_drivers.tektronix import TektronixTPS2012
from qcodes.measure import Measure
from qcodes.plots.qcmatplotlib import MatPlot

logger = logging.getLogger()
logger.setLevel(logging.DEBUG)

Logging hadn't been started.
Activating auto-logging. Current session state plus future input saved.
Filename       : C:\Users\Jens-Work\.qcodes\logs\command_history.log
Mode           : append
Output logging : True
Raw input log  : False
Timestamping   : True
State          : active
Qcodes Logfile : C:\Users\Jens-Work\.qcodes\logs\201006-24644-qcodes.log

In [2]:

tps = TektronixTPS2012("TPS1", "ASRL1::INSTR")

Connected to: TEKTRONIX TPS 2012B (serial:0, firmware:CF:91.1CT FV:v11.10) in 0.44s

In [3]:

# For good measures, one may clear out old messages
tps.clear_message_queue()

SETTING UP AN ACQUISITION¶

The driver supports basic setting of scales and triggers.

In this example, we want to look at a 10 kHz sine, 100 mVpp with a -50 mV offset.

The sine is on channel 1, while the sync (0 V to 3 V square wave) signal from the function generator is on channel 2.

In [4]:

# we don't want to see the ref. signal, only the sine
tps.ch1_state("ON")
tps.ch2_state("OFF")

# horizontal
tps.horizontal_scale.set(10e-6)
# channel 1
tps.ch1_scale.set(50e-3)  # V/div
tps.ch1_position.set(2)  # divisions
# channel 2
tps.ch2_scale.set(1)
tps.ch2_position.set(-3)
# trigger
tps.trigger_type.set("EDGE")
tps.trigger_source.set("CH2")
tps.trigger_level.set(1.5)

ACQUIRING THE CURVES FROM THE OSCILLOSCOPE¶

There is a simple command to get two arrays for the horizontal and vertical data.

Because this is early beta version you must currently call set_set_points on each channel just before reading a trace from the channel. This is a limitation in the current dataset/loop of qcodes. You should also ensure that the scope has been triggered at these settings before calling set_set_points or you will get inconsitent data.

In this example notebook we use force_trigger to ensure that we always have data when setting the set_points

In [5]:

tps.force_trigger()
sleep(10 * tps.horizontal_scale.get_latest())
tps.ch1_curvedata.prepare_curvedata()
tps.ch2_curvedata.prepare_curvedata()
data = Measure(tps.ch1_curvedata, tps.ch2_curvedata).run()

DataSet:
   location = 'data/2017-05-08/#006_{name}_16-21-59'
   <Type>   | <array_id>               | <array.name>      | <array.shape>
   Measured | TPS1_scope_measurement_0 | scope_measurement | (2500,)
   Measured | TPS1_scope_measurement_1 | scope_measurement | (2500,)
acquired at 2017-05-08 16:22:13

In [6]:

plot = MatPlot(subplots=(2, 1))
plot.add(data.TPS1_scope_measurement_0)
plot.add(data.TPS1_scope_measurement_1, subplot=2)

Change horisontal scale and remember to call prepare_curvedata to update the setpoint array

In [7]:

tps.horizontal_scale.set(25e-6)

In [8]:

tps.force_trigger()
sleep(11 * tps.horizontal_scale.get_latest())
tps.ch1_curvedata.prepare_curvedata()
tps.ch2_curvedata.prepare_curvedata()
data2 = Measure(tps.ch1_curvedata, tps.ch2_curvedata).run()

DataSet:
   location = 'data/2017-05-08/#007_{name}_16-22-17'
   <Type>   | <array_id>               | <array.name>      | <array.shape>
   Measured | TPS1_scope_measurement_0 | scope_measurement | (2500,)
   Measured | TPS1_scope_measurement_1 | scope_measurement | (2500,)
acquired at 2017-05-08 16:22:30

In [9]:

plot = MatPlot(subplots=(2, 1))
plot.add(data2.TPS1_scope_measurement_0)
plot.add(data2.TPS1_scope_measurement_1, subplot=2)

In [10]:

tps.close()

In [ ]: